--
-- Juniper Enterprise Specific MIB: RPM MIB
-- 
-- Copyright (c) 2007, Juniper Networks, Inc.
-- All rights reserved.
--
-- The contents of this document are subject to change without notice.
--

JUNIPER-RPM-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32
        FROM SNMPv2-SMI              -- RFC2578
    DateAndTime, TEXTUAL-CONVENTION
        FROM SNMPv2-TC
    CounterBasedGauge64
        FROM HCNUM-TC
    pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex
        FROM DISMAN-PING-MIB
    jnxRpmMibRoot
        FROM JUNIPER-SMI;

jnxRpmMib MODULE-IDENTITY
    LAST-UPDATED "200703010000Z" -- March 1 00:00:00 2007 UTC
    ORGANIZATION "Juniper Networks, Inc."
    CONTACT-INFO
            "        Juniper Technical Assistance Center
                     Juniper Networks, Inc.
                     1194 N. Mathilda Avenue
                     Sunnyvale, CA 94089
                     E-mail: support@juniper.net"

    DESCRIPTION
            "This mib provides data associated with the Realtime Performance
             Monitoring feature."
    -- revision history
    REVISION "200703010000Z" 
    DESCRIPTION
            "Initial definition."
    ::= { jnxRpmMibRoot 1 }


JnxRpmCollectionType ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "Each RPM entry can maintain several collections of probes and
         provide separate calculations over each collection.  The types of
         collections include:

             currentTest       -- the test currently being executed
             lastCompletedTest -- the most recently completed test
             movingAverage     -- the 'n' most recent probes (n is configurable)
             allTests          -- all the probes (since the entry was last
                                  reset).
         
         Objects with this type identify a specific collection."
    SYNTAX INTEGER {  
               currentTest       (1),
               lastCompletedTest (2),
               movingAverage     (3),
               allTests          (4)
           }


JnxRpmMeasurementType ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "For each individual probe, several different measurements can be
         made.  These include the following (all measurements are provided
         in units of microseconds):

             roundTripTime -- this is the delay between the the transmission of 
                 a probe and the arrival of its response.

             rttJitter -- this is the difference between the current round trip 
                 time measurement and the previous one.

             rttInterarrivalJitter -- An estimate of the statistical variance 
                 of a packet's interarrival time.  Defined in rfc1889 as:

                   J=J+(|D(i-1,i)|-J)/16

                 where J is the interarrival jitter and D(i-1, i) is the current
                 round trip jitter measurement. 
  
             egress -- this is the delay beween the transmission of a probe and
                 its arrival at its destination.

             egressJitter -- this is the difference between the current egress
                 delay the previous measurement.

             egressInterarrivalJitter -- similar to rttInterarrivalJitter, but
                 applied to egress jitter measurements.

             ingress -- this is the delay between the transmission of a probe
                 response and its arrival at its destination.

             ingressJitter -- this is the difference between the current ingress
                 delay and the previous measurement.

             ingressInterarrivalJitter -- similar to rttInterarrivalJitter, but
                 applied to ingress jitter measurements.

         Note, not all types of measurements will be performed for every
         probe.  The jitter measurements are available only for those RPM 
         entries that employ hardware timestamps.  Further, the ingress & 
         egress measurements are available only for those probe types that
         measure one-way delays or where hardware timestamps are 
         employed and the one-way-hardware timestamp knob is enabled.  
         In either case, the one-way delays must be less than the round
         trip times, otherwise they are discarded.

         Also note, due to clock synchronization artifacts, many one-way 
         jitter measurements & calculations may include signifacant variations,
         in some cases orders of magnitude greater than the round trip times.
         Because of this, one-way jitter measurements will only be performed
         on samples which are less than 10 seconds apart."
    SYNTAX     INTEGER {
                   roundTripTime             (1),
                   rttJitter                 (2),
                   rttInterarrivalJitter     (3),
                   egress                    (4),
                   egressJitter              (5),
                   egressInterarrivalJitter  (6),
                   ingress                   (7),
                   ingressJitter             (8),
                   ingressInterarrivalJitter (9)
               }


JnxRpmMeasurementSet ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "Over each collection of probes, RPM calculates statistics for several
         sets of measurements.  These sets include the following:

             roundTripTime    -- the set of round trip delays
             posRttJitter     -- the set of positive round trip jitter 
                                 measurements
             negRttJitter     -- the set of negative round trip jitter
                                 measurements
             egress           -- the set of outgoing (source to destination)
                                 one-way delays
             posEgressJitter  -- the set of positive egress jitter measurements
             negEgressJitter  -- the set of negative egress jitter measurements
             ingress          -- the set of incoming (destination to source)
                                 one-way delays
             posIngressJitter -- the set of positive ingress jitter measurements
             negIngressJitter -- the set of negative ingress jitter measurements

        Objects with this type identify a specific set of measurements."
    SYNTAX INTEGER {
               roundTripTime    (1),
               posRttJitter     (2),
               negRttJitter     (3),
               egress           (4),
               posEgressJitter  (5),
               negEgressJitter  (6),
               ingress          (7),
               posIngressJitter (8),
               negIngressJitter (9)
           }


JnxRpmTimestampType ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "This object identifies the type of timestamp used to obtain a
         measurement:

         software
             this indicates software based timestamps
             are used on both client and server.

         clientHardware
             this indicates hardware based timestamps
             are used on the RPM client.  The RPM server
             is processed entirely in software.

         clientAndServerHardware
             this indicates hardware based timestamps
             are used on the RPM client and the server."
    SYNTAX     INTEGER {
                   software                (1),
                   clientHardware          (2),
                   clientAndServerHardware (3)
               }
 

--
-- Sample Results Table
--
    jnxRpmResultsSampleTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmResultsSampleEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides measurements from the latest individual RPM 
             probe samples.  Within each sample, the specific measurement type 
             is identified by jnxRpmResSampleType.  Note, if the latest
             probe was unsuccessful, no measurement types will be available.

             See the definition of JnxRpmMeasurementType for details on
             the types of measurements available."
        ::= { jnxRpmMib 1 }
  
    jnxRpmResultsSampleEntry OBJECT-TYPE
        SYNTAX      JnxRpmResultsSampleEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Each entry provides a specific measurement type for a single
             probe."
        INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxRpmResSampleType }
        ::= { jnxRpmResultsSampleTable 1 }

    JnxRpmResultsSampleEntry ::=
        SEQUENCE {
            jnxRpmResSampleType          JnxRpmMeasurementType,
            jnxRpmResSampleValue         Integer32,
            jnxRpmResSampleTsType        JnxRpmTimestampType,
            jnxRpmResSampleDate          DateAndTime
        }

    jnxRpmResSampleType OBJECT-TYPE
        SYNTAX     JnxRpmMeasurementType
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This object identifies the specific measurement type returned
            by jnxRpmResSampleValue."
       ::= { jnxRpmResultsSampleEntry 1 }

    jnxRpmResSampleValue OBJECT-TYPE
       SYNTAX     Integer32
       MAX-ACCESS read-only
       STATUS     current
       DESCRIPTION
           "This object returns the measurement identified by the corresponding
            jnxRpmResSampleType."
       ::= { jnxRpmResultsSampleEntry 2 }

    jnxRpmResSampleTsType OBJECT-TYPE
       SYNTAX     JnxRpmTimestampType
       MAX-ACCESS read-only
       STATUS     current
       DESCRIPTION
           "This object identifies the type of timestamp used to obtain this
            measurement."
       ::= { jnxRpmResultsSampleEntry 3 }

    jnxRpmResSampleDate OBJECT-TYPE
        SYNTAX     DateAndTime
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the date and time of when this measurement
             was obtained."
        ::= { jnxRpmResultsSampleEntry 4 }


--
-- Summary Results Table
--
    jnxRpmResultsSummaryTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmResultsSummaryEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides a summary of the results for a specific
             RPM entry (identified by pingCtlOwnerIndex/pingCtlTestName).
             The scope of the summary is identified by jnxRpmResSumCollection."
        ::= { jnxRpmMib 2 }
   
    jnxRpmResultsSummaryEntry OBJECT-TYPE
        SYNTAX      JnxRpmResultsSummaryEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Each entry in the table provides a summary of the RPM results
             over a single collection of probes.  For each RPM entry, there
             are several collections maintained: the current test, the
             most recently completed test, a configurable number of the most
             recent probes (aka 'moving average'), and a global collection
             representing all the probes.  Each entry in this table summarizes
             the results for one of these collections."
        INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxRpmResSumCollection }
        ::= { jnxRpmResultsSummaryTable 1 }
        
    JnxRpmResultsSummaryEntry ::=
        SEQUENCE {
            jnxRpmResSumCollection               JnxRpmCollectionType,
            jnxRpmResSumSent                     Unsigned32,
            jnxRpmResSumReceived                 Unsigned32,
            jnxRpmResSumPercentLost              Unsigned32,
            jnxRpmResSumDate                     DateAndTime
        }

    jnxRpmResSumCollection OBJECT-TYPE
        SYNTAX      JnxRpmCollectionType
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This object identifes the collection of probes over which the
             summary data represented by the other objects in this table 
             applies.  Note, if a collection type is not supported or not
             configured, it will not be instantiated in this table."
        ::= { jnxRpmResultsSummaryEntry 1 }

    jnxRpmResSumSent OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the number of probes sent within the 
             collection identified by jnxRpmResSumCollection."
        ::= { jnxRpmResultsSummaryEntry 2 }

    jnxRpmResSumReceived OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the number of probes received within the
             collection identified by jnxRpmResSumCollection."
        ::= { jnxRpmResultsSummaryEntry 3 }

    jnxRpmResSumPercentLost OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the percentage of probes lost within the
             collection identified by jnxRpmResSumCollection."
        ::= { jnxRpmResultsSummaryEntry 4 }

    jnxRpmResSumDate OBJECT-TYPE
        SYNTAX     DateAndTime
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the date and time of when the most recent
             probe within the collection identified by jnxRpmResSumCollection 
             was completed."
        ::= { jnxRpmResultsSummaryEntry 5 }



--
-- Calculated Results Table
--
    jnxRpmResultsCalculatedTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmResultsCalculatedEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides a set of calculated values for each
             RPM entry, for each collection of probes maintained within that
             entry, and for each supported measurement set within that 
             collection of probes.

             Note, not all collection types will be available for every
             RPM Entry (identified by pingCtlOwnerIndex/pingCtlTestName).
             The jitter calculations are available only for those RPM entries 
             that employ hardware timestamps.  Further, the ingress & egress
             calculations are available only for those probe types that
             measure one-way delays or where hardware timestamps are 
             employed and the one-way-hardware timestamp knob is enabled.  
             In either case, the one-way delays must be less than the round
             trip times, otherwise they are discarded.

             Also, this table will skip over any measurement set for which
             there are 0 samples."
        ::= { jnxRpmMib 3 }
  
    jnxRpmResultsCalculatedEntry OBJECT-TYPE
        SYNTAX      JnxRpmResultsCalculatedEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            ""
        INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxRpmResSumCollection,
                jnxRpmResCalcSet }
        ::= { jnxRpmResultsCalculatedTable 1 }

    JnxRpmResultsCalculatedEntry ::=
        SEQUENCE {
            jnxRpmResCalcSet       JnxRpmMeasurementSet,
            jnxRpmResCalcSamples   Unsigned32,
            jnxRpmResCalcMin       Unsigned32,
            jnxRpmResCalcMax       Unsigned32,
            jnxRpmResCalcAverage   Unsigned32,
            jnxRpmResCalcPkToPk    Unsigned32,
            jnxRpmResCalcStdDev    Unsigned32,
            jnxRpmResCalcSum       CounterBasedGauge64
        }

    jnxRpmResCalcSet OBJECT-TYPE
        SYNTAX      JnxRpmMeasurementSet
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This object identifies the measurement set upon which the 
             calculations returned by the other objects in this table are
             based."
        ::= { jnxRpmResultsCalculatedEntry 1 }

    jnxRpmResCalcSamples OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The number of samples used in this calculations."
        ::= { jnxRpmResultsCalculatedEntry 2 }

    jnxRpmResCalcMin OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The minimum of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmResultsCalculatedEntry 3 }

    jnxRpmResCalcMax OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The maximum of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmResultsCalculatedEntry 4 }

    jnxRpmResCalcAverage OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The average of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmResultsCalculatedEntry 5 }

    jnxRpmResCalcPkToPk OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The difference between the minimum and maximum of all the samples 
             in the collection and measurement set associated with this row.  
             Values are provided in units of microseconds."
        ::= { jnxRpmResultsCalculatedEntry 6 }

    jnxRpmResCalcStdDev OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The standard deviation calculated over all the samples 
             in the collection and measurement set associated with this row.  
             Values are provided in units of microseconds."
        ::= { jnxRpmResultsCalculatedEntry 7 }

    jnxRpmResCalcSum OBJECT-TYPE
        SYNTAX     CounterBasedGauge64
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The sum of all the samples in the collection and measurement set 
             associated with this row.  Values are provided in units of 
             microseconds."
        ::= { jnxRpmResultsCalculatedEntry 8 }


--
-- History Sample Table
--
    jnxRpmHistorySampleTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmHistorySampleEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides measurements for individual RPM probe samples.
             In addition to the last completed sample, a configurable number of
             the most recent samples are available as well.  Within each sample,
             the specific measurement type is identified by
             jnxRpmHistSampleType.  Note, if probe was unsuccessful, no 
             measurement types will be available for that history entry.

             See the definition of JnxRpmMeasurementType for details on
             the types of measurements available."
        ::= { jnxRpmMib 4 }
  
    jnxRpmHistorySampleEntry OBJECT-TYPE
        SYNTAX      JnxRpmHistorySampleEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            ""
        INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex,
                jnxRpmHistSampleType }
        ::= { jnxRpmHistorySampleTable 1 }

    JnxRpmHistorySampleEntry ::=
        SEQUENCE {
            jnxRpmHistSampleType          JnxRpmMeasurementType,
            jnxRpmHistSampleValue         Integer32,
            jnxRpmHistSampleTsType        JnxRpmTimestampType
        }

    jnxRpmHistSampleType OBJECT-TYPE
        SYNTAX     JnxRpmMeasurementType
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This object identifies the specific measurement type returned
            by jnxRpmHistSampleValue."
       ::= { jnxRpmHistorySampleEntry 1 }

    jnxRpmHistSampleValue OBJECT-TYPE
       SYNTAX     Integer32
       MAX-ACCESS read-only
       STATUS     current
       DESCRIPTION
           "This object returns the measurement identified by the corresponding
            jnxRpmHistSampleType."
       ::= { jnxRpmHistorySampleEntry 2 }

    jnxRpmHistSampleTsType OBJECT-TYPE
       SYNTAX     JnxRpmTimestampType
       MAX-ACCESS read-only
       STATUS     current
       DESCRIPTION
           "This object identifies the type of timestamp used to obtain this
            measurement."
       ::= { jnxRpmHistorySampleEntry 3 }

     
--
-- History Summary Table
--
    jnxRpmHistorySummaryTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmHistorySummaryEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides historical summary data for each collection
             of probes within each RPM Entry, similar to the
             jnxRpmResultsSummaryTable.  

             In addition to the current summary, this table provides the same 
             number of historical entries as the jnxRpmHistorySampleTable."
        ::= { jnxRpmMib 5 }
  
    jnxRpmHistorySummaryEntry OBJECT-TYPE
        SYNTAX      JnxRpmHistorySummaryEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            ""
        INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex,
                jnxRpmHistSumCollection }
        ::= { jnxRpmHistorySummaryTable 1 }

    JnxRpmHistorySummaryEntry ::=
        SEQUENCE {
            jnxRpmHistSumCollection  JnxRpmCollectionType,
            jnxRpmHistSumSent        Unsigned32,
            jnxRpmHistSumReceived    Unsigned32,
            jnxRpmHistSumPercentLost Unsigned32
        }

    jnxRpmHistSumCollection OBJECT-TYPE
        SYNTAX      JnxRpmCollectionType
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Identifies the collection of probes whose results are summarized by
             this row.  

             At this time, historical summaries are available only for the 
             current test (currentTest(1))."
        ::= { jnxRpmHistorySummaryEntry 1 }

    jnxRpmHistSumSent OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the number of probes sent within the 
             collection identified by jnxRpmHistSumCollection."
        ::= { jnxRpmHistorySummaryEntry 2 }

    jnxRpmHistSumReceived OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the number of probes received within the 
             collection identified by jnxRpmHistSumCollection."
        ::= { jnxRpmHistorySummaryEntry 3 }

    jnxRpmHistSumPercentLost OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object provides the percentage of probes lost within the 
             collection identified by jnxRpmHistSumCollection."
        ::= { jnxRpmHistorySummaryEntry 4 }



--
-- History Calculated Table
--
    jnxRpmHistoryCalculatedTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF JnxRpmHistoryCalculatedEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table provides a set of calculated values for each
             RPM entry, for each collection of probes maintained within that
             entry, and for each supported calculated type within that 
             collection of probes, similar to the jnxRpmResultsCalculatedTable.

             In addition to the current summary, this table provides the same 
             number of historical entries as the jnxRpmHistorySampleTable."
        ::= { jnxRpmMib 6 }
  
    jnxRpmHistoryCalculatedEntry OBJECT-TYPE
        SYNTAX      JnxRpmHistoryCalculatedEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            ""
        INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex,
                jnxRpmHistSumCollection, jnxRpmHistCalcSet }
        ::= { jnxRpmHistoryCalculatedTable 1 }

    JnxRpmHistoryCalculatedEntry ::=
        SEQUENCE {
            jnxRpmHistCalcSet       JnxRpmMeasurementSet,
            jnxRpmHistCalcSamples   Unsigned32,
            jnxRpmHistCalcMin       Unsigned32,
            jnxRpmHistCalcMax       Unsigned32,
            jnxRpmHistCalcAverage   Unsigned32,
            jnxRpmHistCalcPkToPk    Unsigned32,
            jnxRpmHistCalcStdDev    Unsigned32,
            jnxRpmHistCalcSum       CounterBasedGauge64
        }

    jnxRpmHistCalcSet OBJECT-TYPE
       SYNTAX     JnxRpmMeasurementSet
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
            "This object identifies the measurement set upon which the 
             calculations returned by the other objects in this table are
             based."
       ::= { jnxRpmHistoryCalculatedEntry 1 }

    jnxRpmHistCalcSamples OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The number of samples used in this calculations."
        ::= { jnxRpmHistoryCalculatedEntry 2 }

    jnxRpmHistCalcMin OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The minimum of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 3 }

    jnxRpmHistCalcMax OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The maximum of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 4 }

    jnxRpmHistCalcAverage OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The average of all the samples in the collection and measurement
             set associated with this row.  Values are provided in units
             of microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 5 }

    jnxRpmHistCalcPkToPk OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The difference between the minimum and maximum of all the samples 
             in the collection and measurement set associated with this row.  
             Values are provided in units of microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 6 }

    jnxRpmHistCalcStdDev OBJECT-TYPE
        SYNTAX     Unsigned32
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The standard deviation calculated over all the samples 
             in the collection and measurement set associated with this row.  
             Values are provided in units of microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 7 }

    jnxRpmHistCalcSum OBJECT-TYPE
        SYNTAX     CounterBasedGauge64
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "The sum of all the samples in the collection and measurement set 
             associated with this row.  Values are provided in units of 
             microseconds."
        ::= { jnxRpmHistoryCalculatedEntry 8 }

END